Spicer Style Driveshaft Universal Joint
Fits 41-66 MB, GPW, CJ-2A, 3A, 3B, 5, M38, M38A1
New Spicer Style Universal Joint (4 required per vehicle)
Includes complete universal joint with bearing caps and retainer clips. Attaches yoke and propeller shaft ends together on 4wd vehicles.
Fits:
41-45 MB
41-45 GPW
46-49 CJ-2A
49-53 CJ-3A
53-64 CJ-3B
55-66 CJ-5
50-52 M38
52-66 M38A1
| Part # | Price |
|---|---|
| 8126614S | $23.99 MSRP: |
$23.99
MSRP:
Questions & Answers
This is for the driveshaft only. If you have a replacement style spicer front axle shaft that is part number: 937340
Be the first to answer this question.
This would be for your drive shafts only. 909476 would be for the axle shaft.
Be the first to answer this question.
Yes, this is the proper one, they are the same front and rear driveshafts. There are 4 per vehicle.
Be the first to answer this question.
The MB/GPW book lists 2 different part numbers for the rear driveshaft ends: Spicer 1261 and 1268. Are yours compatible with the originals? Also, do the cross "T" parts have groves in the ends to allow grease to pass easily to the needles?
Willys Jeep Parts Tech:
This u joint can be used for all 4 points on the MB/GPW. There is a zerk fitting on these, so grease is able to get to the rollers internally.
This u joint can be used for all 4 points on the MB/GPW. There is a zerk fitting on these, so grease is able to get to the rollers internally.
Do you sell just the bearing caps & Pins? Thanks. 1964 CJ5 Willys F134.
Willys Jeep Parts Tech:
Give me a call toll free so we can see if we can get that set up for you. Thanks
Give me a call toll free so we can see if we can get that set up for you. Thanks
What size ujoints are these? 1310? What is the diameter of the cap and the length of the ujoint? Thanks,
Hank:
I checked those dimensions and they are for 1310, 297X and 760X. All the same dimensions.
I checked those dimensions and they are for 1310, 297X and 760X. All the same dimensions.
Willys Jeep Parts Tech:
Diameter 1.650 at end caps. Overall length 3.25 end cap to end cap across.
Diameter 1.650 at end caps. Overall length 3.25 end cap to end cap across.
I have a Jeep I built when I was in California to go on the trails. It has a lot of miscellaneous parts on it. The rear driveshaft has spicer u-joints that have a number on the cap (P051), the front ones have a different one (P541) and are smaller. Which ones do I need? The front from end to end is 2.44 and the cap is 1.065. The rear are 3.22 end and 1.076 cap.
Willys Jeep Parts Tech:
Sounds like you have a later CJ-5 1966+ Please call us toll free and we can ID what you have there.
Sounds like you have a later CJ-5 1966+ Please call us toll free and we can ID what you have there.
I have a 66 CJ5 with the Dana 27 ront, Dana 44 rear, and Dana 18 transfer case. Dauntless V6. Will these u-joints fit the front and rear driveshafts?
Willys Tech:
In that year you could have these or part number: 937340
In that year you could have these or part number: 937340
I have a universal joint with no snap rings. Instead there is a milled portion of all four ends to accept retaining clips that are bolted to the yoke. The universal joint has to be installed between all four yokes then the end caps with needle bearings have to be pushed onto the ends of the universal joints. Then the retaining clips are bolted onto the yokes to hold the assembly together. I cant find anything like it in any of your catalogs.I need to replace many of these as they are shot.
Willys Tech:
Sounds like you have the cleveland style joint. Part number: 924189 will replace it. They typically used that style on Willys Truck and Station Wagons.
Sounds like you have the cleveland style joint. Part number: 924189 will replace it. They typically used that style on Willys Truck and Station Wagons.
YOU MIGHT ALSO BE INTERESTED IN
